#
- 3-tab shingle
- A flat asphalt shingle with three even tabs per strip, giving a uniform look.
- 5V-crimp
- A metal panel with five V-shaped ribs, common on traditional and coastal homes.
A
- Algae resistance
- Granules treated to slow the dark streaks algae cause on shingles in humid climates.
- Aluminum-zinc coating
- A metallic coating of aluminum and zinc on steel that protects it from rust. Sold bare or under paint.
- Anchor (fall protection)
- A secure point on the roof that a worker's lifeline attaches to.
B
- Backer coat
- The thin paint coat on the underside of a painted metal panel.
- Ballasted roof
- A low-slope membrane held down by stone or pavers instead of fasteners or adhesive.
- Barrel tile
- A rounded, S-shaped or two-piece roof tile used on Spanish and Mission-style roofs.
- Base trim
- Trim at the bottom of metal wall panels that closes the gap at the foundation.
- Batten
- A strip of wood or metal fastened to the roof that tile, stone-coated panels or metal panels attach to.
- Board and batten
- A siding style with wide vertical boards and narrow raised strips over the joints.
- Built-up roofing (BUR)
- A low-slope roof of several layers of felt and asphalt, often topped with gravel.
- Butyl tape
- A sticky, flexible tape that stays soft, used to seal metal panel laps and trim joints.
C
- Cap nail
- A roofing nail with a wide plastic cap, used to fasten synthetic underlayment.
- Chalking
- A fine powder that forms on painted surfaces as the paint weathers.
- Class 4
- The highest impact rating for roofing, based on a 2″ steel ball test.
- Class A
- The highest fire rating for roof coverings.
- Clip (standing seam)
- A hidden bracket that holds a standing seam panel to the deck while allowing it to move.
- Closure strip
- A foam or rubber strip shaped to fill the gaps under ribbed metal panels at the eave and ridge.
- Coil
- A large roll of flat sheet metal from which panels and trim are formed.
- Concealed fastener
- A fastener hidden under the next panel or a seam, as on standing seam.
- Condensation
- Water that forms when warm, moist air touches a cold surface.
- Coping
- Metal cap over the top of a parapet wall.
- Corrugated panel
- A metal panel with a rounded, wavy profile.
- Counter-batten
- Battens running up the slope under horizontal battens, creating an air and drainage gap.
- Cover board
- A rigid board laid over insulation to protect it and support the membrane on low-slope roofs.
- Cricket
- A small peaked structure behind a chimney or curb that diverts water around it.
- Curb
- A raised frame on a roof that an HVAC unit, skylight or hatch sits on.
- Cut list
- A list of panel lengths and quantities for ordering panels made to length.
D
- Deck
- The structural surface, usually plywood or OSB, that roofing is installed on.
- Dew point
- The temperature at which moisture in the air condenses into water.
- Dimensional shingle
- A laminated asphalt shingle with two or more layers for a textured look. Also called architectural or laminated.
- Dormer
- A structure that projects from a sloped roof, usually with a window.
- Double lock
- A standing seam folded 180° twice for the tightest seal, used on low slopes.
- Downspout
- The vertical pipe that carries water from the gutter to the ground.
- Drip edge
- Metal trim at the roof edge that directs water away from the fascia.
E
- Eave
- The lower edge of a roof, usually overhanging the wall.
- Eave strut
- A sloped steel member at the eave of a metal building, where the roof meets the wall.
- Endwall flashing
- Flashing where the top of a roof meets a vertical wall.
- EPDM
- A synthetic rubber single-ply membrane for low-slope roofs.
- Expansion and contraction
- The way metal grows and shrinks with temperature; also called thermal movement.
- Exposed fastener
- A screw that goes through the face of the panel and stays visible.
F
- Fascia
- The vertical board along the eave that gutters often attach to.
- Felt
- An asphalt-saturated underlayment, usually #15 or #30.
- Field (of the roof)
- The main open area of a roof, away from edges and penetrations.
- Flashing
- Metal or membrane pieces that seal joints and edges where water could get in.
- Furring strip
- A thin strip fastened to a surface to create a flat base or air gap.
G
- Gable
- The triangular wall at the end of a pitched roof.
- Galvanized
- Steel coated with zinc for rust protection.
- Gauge
- A number for sheet metal thickness; the lower the number, the thicker the steel.
- Girt
- A horizontal framing member on the walls of a metal building that wall panels attach to.
- Girth
- The total flat width of a trim piece before it's bent.
- Granules
- The small mineral or stone particles on the surface of shingles and stone-coated panels.
- Gutter
- A channel along the eave that collects water from the roof.
H
- Hat channel
- A hat-shaped steel strip used as a purlin or furring strip.
- Hem
- An edge of metal folded back on itself for strength and safety.
- High-temperature underlayment
- Underlayment rated for the heat under metal roofs.
- Hip
- The sloped ridge where two roof planes meet at an outside corner.
I
- Ice dam
- A ridge of ice at the eave that traps melting snow, which can back up under the roofing.
- Impact rating
- A rating that shows how well roofing resists hail, from Class 1 to Class 4.
- Induction welding
- A way to attach a membrane to hidden plates with heat from an induction tool.
J
- J-channel
- Trim shaped like a J that holds and finishes cut edges of siding.
L
- Lap
- Where one panel, sheet or piece overlaps another.
- Lap siding
- Horizontal siding planks that overlap each other.
- Liner panel
- A light metal panel on the inside walls or ceiling of a building.
- Low-slope roof
- A roof with a pitch under about 3:12.
M
- Mechanical seam
- A standing seam folded closed with a seaming tool after installation.
- Membrane
- A continuous waterproof sheet used on low-slope roofs.
- Mil
- One-thousandth of an inch, used to measure membrane thickness.
- Modified bitumen
- An asphalt roofing sheet reinforced with polyester or fiberglass, for low-slope roofs.
N
- Nail-strip panel
- A standing seam panel fastened through a slotted flange hidden by the next panel.
- Net free area (NFA)
- The open area of a vent, used to size attic ventilation.
- Nibbler
- A power tool that cuts metal by punching out small bits, without heat.
O
- Oil canning
- Visible waviness in the flat areas of metal panels.
- OSB
- Oriented strand board, a common roof and wall deck material.
- Overhang
- The part of a roof or panel that extends past the wall or eave.
P
- Panel coverage
- The width a panel covers once installed, after side laps.
- Parapet
- A low wall that extends above the roof line, common on commercial buildings.
- PBR panel
- An R-panel with a purlin bearing leg for a stronger side lap.
- Penetration
- Anything that goes through the roof, such as a pipe, vent or skylight.
- Pipe boot
- A flexible flashing that seals around a pipe through the roof.
- Pitch
- The slope of a roof, given as rise over 12 inches of run, such as 6:12.
- Pitch factor
- A number used to convert a roof's flat footprint to its sloped surface area.
- Polyiso
- Polyisocyanurate, a rigid foam insulation board common on commercial roofs.
- Purlin
- A horizontal framing member that roof panels attach to.
- PVC membrane
- A thermoplastic single-ply membrane with strong grease and chemical resistance.
- PVDF
- A premium fluoropolymer paint for metal with the best fade resistance.
R
- R-panel
- A common through-fastened metal panel with tall trapezoid ribs about 12″ apart.
- R-value
- A measure of how well insulation resists heat flow. Higher is better.
- Radiant barrier
- A reflective foil layer that reduces heat transfer from a hot roof.
- Rake
- The sloped edge of a roof at the gable end.
- Re-roof
- Replacing an existing roof, with or without tearing off the old one.
- Recover
- A new roof installed over an existing low-slope roof.
- Ridge
- The horizontal peak where two roof planes meet.
- Ridge cap
- Trim or shingles that cover the ridge.
- Ridge vent
- A vent along the ridge that lets warm attic air out.
- Rivet
- A fastener used to join trim and flashing pieces, set with a rivet tool.
- Roof measurement report
- A report, often from aerial images, listing a roof's squares, pitches and edge lengths.
S
- Seamer
- A hand or power tool that folds standing seams closed.
- Self-adhered underlayment
- A rubberized sheet with a peel-off back that sticks to the deck and seals around fasteners.
- Self-drilling screw
- A screw with a drill point that drills its own hole in steel.
- Sheathing
- Boards or panels covering the framing of a roof or wall.
- Shed roof
- A single-slope roof.
- Sidewall flashing
- Flashing where the sloped side of a roof meets a wall.
- Single-ply
- A low-slope roof membrane installed in one layer, such as TPO, PVC or EPDM.
- Slate
- Natural stone split into thin roofing pieces; also made as synthetic slate.
- SMP
- Silicone-modified polyester, the most common paint system for metal roofing.
- Snap-lock
- A standing seam panel that snaps together by hand without a seaming tool.
- Snow guard
- A device that holds snow on a metal roof so it doesn't slide off in one piece.
- Soffit
- The underside of the roof overhang.
- Square
- 100 square feet of roof surface.
- Standing seam
- A metal roof with hidden fasteners and raised seams joining the panels.
- Starter strip
- The first course of shingles or a special strip at the eave that seals the first row.
- Stitch screw
- A short screw that joins two panels or panel and trim at a lap.
- Stone-coated steel
- Steel roofing panels finished with stone granules for a tile, shake or shingle look.
- Striations
- Small lines rolled into the flat of a metal panel to reduce oil canning.
- Structural standing seam
- A heavy standing seam system that spans open purlins without a solid deck.
- Swarf
- Metal shavings from drilling or cutting, which can rust on panels if not swept off.
- Synthetic underlayment
- A polymer sheet underlayment, lighter and stronger than felt.
T
- Tapered insulation
- Insulation boards cut to slope, used to drain water on flat roofs.
- Tear-off
- Removing the old roof down to the deck before re-roofing.
- TPO
- Thermoplastic polyolefin, a white heat-welded single-ply membrane for low-slope roofs.
- Transition flashing
- Flashing where the roof pitch changes.
U
- Underlayment
- The water-resistant layer installed between the deck and the roofing.
V
- Valley
- The inside corner where two roof planes meet and water collects.
- Vapor retarder
- A layer that slows moisture moving through insulation, used to prevent condensation.
- Vented soffit
- Soffit with perforations or slots that let air into the attic.
W
- Wainscot
- A band of different siding or color on the lower part of a wall.
- Washer (sealing)
- The rubber washer under a screw head that seals the hole in a metal panel.
- Wind uplift
- The force of wind pulling a roof upward; roofs are tested and rated for it.