Roofing, siding and metal building materials for contractors, builders and designersServing the U.S.
Home › Resources › Glossary

Glossary

Roofing, siding and metal building terms explained in plain language.

crew reviewing plans

#

3-tab shingle
A flat asphalt shingle with three even tabs per strip, giving a uniform look.
5V-crimp
A metal panel with five V-shaped ribs, common on traditional and coastal homes.

A

Algae resistance
Granules treated to slow the dark streaks algae cause on shingles in humid climates.
Aluminum-zinc coating
A metallic coating of aluminum and zinc on steel that protects it from rust. Sold bare or under paint.
Anchor (fall protection)
A secure point on the roof that a worker's lifeline attaches to.

B

Backer coat
The thin paint coat on the underside of a painted metal panel.
Ballasted roof
A low-slope membrane held down by stone or pavers instead of fasteners or adhesive.
Barrel tile
A rounded, S-shaped or two-piece roof tile used on Spanish and Mission-style roofs.
Base trim
Trim at the bottom of metal wall panels that closes the gap at the foundation.
Batten
A strip of wood or metal fastened to the roof that tile, stone-coated panels or metal panels attach to.
Board and batten
A siding style with wide vertical boards and narrow raised strips over the joints.
Built-up roofing (BUR)
A low-slope roof of several layers of felt and asphalt, often topped with gravel.
Butyl tape
A sticky, flexible tape that stays soft, used to seal metal panel laps and trim joints.

C

Cap nail
A roofing nail with a wide plastic cap, used to fasten synthetic underlayment.
Chalking
A fine powder that forms on painted surfaces as the paint weathers.
Class 4
The highest impact rating for roofing, based on a 2″ steel ball test.
Class A
The highest fire rating for roof coverings.
Clip (standing seam)
A hidden bracket that holds a standing seam panel to the deck while allowing it to move.
Closure strip
A foam or rubber strip shaped to fill the gaps under ribbed metal panels at the eave and ridge.
Coil
A large roll of flat sheet metal from which panels and trim are formed.
Concealed fastener
A fastener hidden under the next panel or a seam, as on standing seam.
Condensation
Water that forms when warm, moist air touches a cold surface.
Coping
Metal cap over the top of a parapet wall.
Corrugated panel
A metal panel with a rounded, wavy profile.
Counter-batten
Battens running up the slope under horizontal battens, creating an air and drainage gap.
Cover board
A rigid board laid over insulation to protect it and support the membrane on low-slope roofs.
Cricket
A small peaked structure behind a chimney or curb that diverts water around it.
Curb
A raised frame on a roof that an HVAC unit, skylight or hatch sits on.
Cut list
A list of panel lengths and quantities for ordering panels made to length.

D

Deck
The structural surface, usually plywood or OSB, that roofing is installed on.
Dew point
The temperature at which moisture in the air condenses into water.
Dimensional shingle
A laminated asphalt shingle with two or more layers for a textured look. Also called architectural or laminated.
Dormer
A structure that projects from a sloped roof, usually with a window.
Double lock
A standing seam folded 180° twice for the tightest seal, used on low slopes.
Downspout
The vertical pipe that carries water from the gutter to the ground.
Drip edge
Metal trim at the roof edge that directs water away from the fascia.

E

Eave
The lower edge of a roof, usually overhanging the wall.
Eave strut
A sloped steel member at the eave of a metal building, where the roof meets the wall.
Endwall flashing
Flashing where the top of a roof meets a vertical wall.
EPDM
A synthetic rubber single-ply membrane for low-slope roofs.
Expansion and contraction
The way metal grows and shrinks with temperature; also called thermal movement.
Exposed fastener
A screw that goes through the face of the panel and stays visible.

F

Fascia
The vertical board along the eave that gutters often attach to.
Felt
An asphalt-saturated underlayment, usually #15 or #30.
Field (of the roof)
The main open area of a roof, away from edges and penetrations.
Flashing
Metal or membrane pieces that seal joints and edges where water could get in.
Furring strip
A thin strip fastened to a surface to create a flat base or air gap.

G

Gable
The triangular wall at the end of a pitched roof.
Galvanized
Steel coated with zinc for rust protection.
Gauge
A number for sheet metal thickness; the lower the number, the thicker the steel.
Girt
A horizontal framing member on the walls of a metal building that wall panels attach to.
Girth
The total flat width of a trim piece before it's bent.
Granules
The small mineral or stone particles on the surface of shingles and stone-coated panels.
Gutter
A channel along the eave that collects water from the roof.

H

Hat channel
A hat-shaped steel strip used as a purlin or furring strip.
Hem
An edge of metal folded back on itself for strength and safety.
High-temperature underlayment
Underlayment rated for the heat under metal roofs.
Hip
The sloped ridge where two roof planes meet at an outside corner.

I

Ice dam
A ridge of ice at the eave that traps melting snow, which can back up under the roofing.
Impact rating
A rating that shows how well roofing resists hail, from Class 1 to Class 4.
Induction welding
A way to attach a membrane to hidden plates with heat from an induction tool.

J

J-channel
Trim shaped like a J that holds and finishes cut edges of siding.

L

Lap
Where one panel, sheet or piece overlaps another.
Lap siding
Horizontal siding planks that overlap each other.
Liner panel
A light metal panel on the inside walls or ceiling of a building.
Low-slope roof
A roof with a pitch under about 3:12.

M

Mechanical seam
A standing seam folded closed with a seaming tool after installation.
Membrane
A continuous waterproof sheet used on low-slope roofs.
Mil
One-thousandth of an inch, used to measure membrane thickness.
Modified bitumen
An asphalt roofing sheet reinforced with polyester or fiberglass, for low-slope roofs.

N

Nail-strip panel
A standing seam panel fastened through a slotted flange hidden by the next panel.
Net free area (NFA)
The open area of a vent, used to size attic ventilation.
Nibbler
A power tool that cuts metal by punching out small bits, without heat.

O

Oil canning
Visible waviness in the flat areas of metal panels.
OSB
Oriented strand board, a common roof and wall deck material.
Overhang
The part of a roof or panel that extends past the wall or eave.

P

Panel coverage
The width a panel covers once installed, after side laps.
Parapet
A low wall that extends above the roof line, common on commercial buildings.
PBR panel
An R-panel with a purlin bearing leg for a stronger side lap.
Penetration
Anything that goes through the roof, such as a pipe, vent or skylight.
Pipe boot
A flexible flashing that seals around a pipe through the roof.
Pitch
The slope of a roof, given as rise over 12 inches of run, such as 6:12.
Pitch factor
A number used to convert a roof's flat footprint to its sloped surface area.
Polyiso
Polyisocyanurate, a rigid foam insulation board common on commercial roofs.
Purlin
A horizontal framing member that roof panels attach to.
PVC membrane
A thermoplastic single-ply membrane with strong grease and chemical resistance.
PVDF
A premium fluoropolymer paint for metal with the best fade resistance.

R

R-panel
A common through-fastened metal panel with tall trapezoid ribs about 12″ apart.
R-value
A measure of how well insulation resists heat flow. Higher is better.
Radiant barrier
A reflective foil layer that reduces heat transfer from a hot roof.
Rake
The sloped edge of a roof at the gable end.
Re-roof
Replacing an existing roof, with or without tearing off the old one.
Recover
A new roof installed over an existing low-slope roof.
Ridge
The horizontal peak where two roof planes meet.
Ridge cap
Trim or shingles that cover the ridge.
Ridge vent
A vent along the ridge that lets warm attic air out.
Rivet
A fastener used to join trim and flashing pieces, set with a rivet tool.
Roof measurement report
A report, often from aerial images, listing a roof's squares, pitches and edge lengths.

S

Seamer
A hand or power tool that folds standing seams closed.
Self-adhered underlayment
A rubberized sheet with a peel-off back that sticks to the deck and seals around fasteners.
Self-drilling screw
A screw with a drill point that drills its own hole in steel.
Sheathing
Boards or panels covering the framing of a roof or wall.
Shed roof
A single-slope roof.
Sidewall flashing
Flashing where the sloped side of a roof meets a wall.
Single-ply
A low-slope roof membrane installed in one layer, such as TPO, PVC or EPDM.
Slate
Natural stone split into thin roofing pieces; also made as synthetic slate.
SMP
Silicone-modified polyester, the most common paint system for metal roofing.
Snap-lock
A standing seam panel that snaps together by hand without a seaming tool.
Snow guard
A device that holds snow on a metal roof so it doesn't slide off in one piece.
Soffit
The underside of the roof overhang.
Square
100 square feet of roof surface.
Standing seam
A metal roof with hidden fasteners and raised seams joining the panels.
Starter strip
The first course of shingles or a special strip at the eave that seals the first row.
Stitch screw
A short screw that joins two panels or panel and trim at a lap.
Stone-coated steel
Steel roofing panels finished with stone granules for a tile, shake or shingle look.
Striations
Small lines rolled into the flat of a metal panel to reduce oil canning.
Structural standing seam
A heavy standing seam system that spans open purlins without a solid deck.
Swarf
Metal shavings from drilling or cutting, which can rust on panels if not swept off.
Synthetic underlayment
A polymer sheet underlayment, lighter and stronger than felt.

T

Tapered insulation
Insulation boards cut to slope, used to drain water on flat roofs.
Tear-off
Removing the old roof down to the deck before re-roofing.
TPO
Thermoplastic polyolefin, a white heat-welded single-ply membrane for low-slope roofs.
Transition flashing
Flashing where the roof pitch changes.

U

Underlayment
The water-resistant layer installed between the deck and the roofing.

V

Valley
The inside corner where two roof planes meet and water collects.
Vapor retarder
A layer that slows moisture moving through insulation, used to prevent condensation.
Vented soffit
Soffit with perforations or slots that let air into the attic.

W

Wainscot
A band of different siding or color on the lower part of a wall.
Washer (sealing)
The rubber washer under a screw head that seals the hole in a metal panel.
Wind uplift
The force of wind pulling a roof upward; roofs are tested and rated for it.