
Fasteners
| Fastener | What it is | Typical sizes | Common uses |
|---|---|---|---|
| Wood-grip screw | Sharp-point screw with a sealing washer | #9 to #10, 1″ to 2½″ | Metal panels over wood purlins or decking |
| Self-drilling metal screw | Drill-point screw with a sealing washer | #12 to #14, ¾″ to 2″ | Metal panels over steel purlins and girts |
| Stitch (lap) screw | Short screw for joining two sheets | #14, ½″ to 1″ | Panel side laps, trim to panel |
| Pancake-head screw | Low-profile head, no washer | #10 to #12, 1″ to 1½″ | Standing seam clips, nail-strip panels |
| Rivets (pop rivets) | Blind rivets in painted or bare metal | ⅛″ and ¼″ | Trim, gutters, flashing details |
| Roofing nails | Coil or hand nails with large heads | 1″ to 2″ | Shingles, felt, some tile |
| Cap nails and cap staples | Nails or staples with plastic caps | 1″ and longer | Synthetic underlayment |
| Tile fasteners | Nails, screws, clips and foam adhesive for tile | Varies | Clay and concrete tile |
Sizes, coatings and drill points vary by manufacturer. Your quote lists the exact specs.
Washers. Screws for metal panels use a bonded washer, often EPDM rubber, under the head. It seals the hole and must be compressed just enough: snug and flat, not crushed.
Coatings and colors. Fasteners come with corrosion-resistant coatings, and painted heads in the same colors as the panels. Stainless steel heads or full stainless screws suit coastal and corrosive areas.
Matching the screw to the framing. Wood framing uses wood-grip screws; steel framing uses self-drilling screws with a drill point sized to the steel thickness.
Sealants and tapes
| Product | What it is | Common uses |
|---|---|---|
| Butyl tape | Sticky, flexible tape that stays soft | Panel side laps, closure strips, trim laps |
| Polyurethane sealant | Tough, paintable sealant | Trim and flashing joints |
| Silicone sealant | Flexible, UV-resistant sealant | Metal and low-slope details |
| Tri-polymer / hybrid sealant | Sealant made to bond metal and stay flexible | Metal roofing and gutters |
| Roofing cement | Asphalt-based mastic | Shingle and low-slope repairs, flashing |
| Foam sealant / adhesive | Expanding foam made for roofing | Tile setting, gaps |
Choose sealants that are rated for the roofing material and color-match where they show.
Closures, pipe flashings and other accessories
- Closure strips: foam or rubber strips shaped to the panel profile, used at the eave (inside closures) and ridge (outside closures). Vented closures allow airflow at the ridge.
- Pipe flashings (pipe boots): rubber or silicone boots with flexible bases that seal around vent pipes on metal roofs, and lead or plastic boots for shingle roofs.
- Snow guards and snow retention bars: keep snow and ice from sliding off metal roofs in one piece. Clamp-on styles attach to standing seams without holes.
- Seam clamps: non-penetrating clamps for mounting solar racks, snow guards, signs and lines to standing seam roofs.
- Curbs and roof jacks: for HVAC units, skylights and other penetrations.
- Touch-up paint: small bottles or pens to cover scratches and cut edges.
Installation basics
- Use the screw count and pattern from the panel manufacturer, usually in the flat next to the rib or on the rib, depending on the panel.
- Drive screws straight and stop when the washer is snug; a crooked or over-driven screw is a common leak point.
- Sweep away drill shavings (swarf) the same day so they don't rust on the panels.
- Put butyl tape and closures in before the panel or trim goes on, not after.
Always follow the manufacturer's instructions.
What to include in your quote request
- Panel type and color to match
- Framing type: wood or steel, and its thickness
- Roof and wall size, or the panel quote these parts go with
- Accessories needed: closures, pipe flashings, snow guards, sealants, touch-up
- Job location
Related products
Common questions
How many screws do I need per square?
It depends on the panel and the purlin spacing. A common range is about 70 to 80 screws per square for exposed-fastener panels. The panel manufacturer's pattern sets the number.
Do screws need to match the panel color?
They don't have to, but color-matched heads look better and the paint adds protection.
What is the best sealant for metal roofs?
A sealant made for metal, such as butyl tape for laps and a tri-polymer or similar sealant for trim. Avoid sealants that aren't rated for metal or UV exposure.
Do I need snow guards?
In snow country they're common, to keep snow from sliding off in sheets over doors, walkways and lower roofs. In warm climates they're mostly added over entries.
What size drill point do I need?
Match the drill point to the steel thickness of the framing. Thicker purlins need a longer drill point.
